Barcode printers often encounter some problems during use. The following are some common faults encountered in long-term sales and use of Zebra Zebra barcode printers. They are summarized in the following list and adjusted. I hope to use Zebra Zebra barcode machine for you. Helpful.
First, the printer has some errors: There are several kinds of errors that will affect the normal printing of the barcode printer. Some will stop the printer, while others will only remind the operator, and will not affect the printing.
If the print head is opened incorrectly, the whole printer will stop printing. If the print head temperature is low, it will not affect the specific use and still operate normally.
The label runs out of error, the ribbon runs out of error, the print head is open, and the cutter is wrong.
After using the label, running out of ribbon, the cutter is wrong. It will stop the printer from printing. Then the error light will be on. The print head is open and the error light will just flash. Once one or more of the above errors occur, the printer The Pause light will be illuminated. Then wait for the user to eliminate the error. Once the user has eliminated the error, the user can press the Pause button to put the printer in normal working condition. Of course, if the printer is in the print label state before the error occurs, then it is cleared. After the error, the printer will continue the previous print job.
The print head is too hot, all print jobs will stop. Then the error light will flash slowly. Once the temperature of the print head returns to normal, the printer will continue to print its tasks. When the print head overheats, the printer Other functions are still normal. For example, Feed, and calibrate are normal.
The print head is too cold, the printer will have a similar situation when the print head temperature becomes lower. But the difference is that the printer does not stop printing. Only the error light will flash slowly. So the print head temperature has passed. Low does not affect normal use.
The power supply is too hot. When the power supply becomes very hot, all print jobs will stop. At this time, the error light will flash slowly. When the temperature drops again, the printer will continue to print normally. It is similar to the phenomenon. The print head is overheated.
The following is the case of ERROR in some error situations.
Panel LED light, print head open, ribbon run out label, print head too cold, print head too hot, power supply too hot, Error faster flashing, steady, steady, slower blinking, slower Flashing, slower flashing.
Second, the Led display error message and error report: Ribbon Out problem solution, in the thermal transfer state, the ribbon is not installed to reload the ribbon, in the thermal transfer state, the ribbon sensor is not very good The measured ribbon value. Re-recognize the paper and ribbon, in the thermal mode, and the ribbon is not used. Remove the ribbon, please make sure the driver and software settings are correct, Paper out, paper is not installed, Or the paper is not loaded, the paper is reloaded, the sensor is not moved to a better position, the reflective sensor is moved to the appropriate position, the printer is set to non-continuous paper, but the continuous paper is used, and the printer is reset to the appropriate paper type. Make sure the settings in the printer driver are correct, re-recognize the paper, the media sensor is not selected, select sensor select in the menu and reselect sensor. The print head is not closed, close the print head, the ribbon is not loaded correctly, and the print is blocked. Head sensor, reload the ribbon,>Ribbon In, the print mode setting is not correct. Set the correct printing method in the print method. Please confirm the software or driver settings. Correct, the ribbon is installed, and the correct printing method is set in the print method. Please confirm that the settings in the software or driver are correct. Out Of Memory. There is not enough memory to execute the next instruction, please confirm your PCMCIA card, and FLASH The installation is normal or working properly.
Third, the print quality problem. Part of the location print missing print head broken needle. Replace the print head. The print head has dirt to clean the print head.. Wrong print position, paper feed error. Printer sensor error, adjust the printer's sensor left and right position. Or seek technical skills. The paper type of the printer is wrong, the setting of continuous paper or non-continuous paper is wrong. Set to the correct type: Ribbon wrinkle. The ribbon is not in the correct position when you take the paper, reinstall the ribbon. Wrong printing Depth setting, set the temperature of some paper. The wrong print head pressure re-adjusts the pressure of the print head.
Fourth, some solutions to software-related problems that are often encountered.
1, I use the zebra \Zebra machine random software BARONE can not print Chinese.. A: Please enter the BARONE installation directory, and then enter the BIN directory. Modify the setup.ini, all the semicolons before the printer below the statement are deleted. These statements are: .TTFSizeThreshold=1.TTFROTATETHRESHOLD=1.Rotatethreshold=1. Then enter the BarOne program to play Chinese. Remember to choose Chinese fonts.
2, my machine prints too light. Does not meet my requirements. A: Enter the printer panel to adjust the darkness.
3, my printer speed suddenly has a retracting action, much slower than before. A: Enter the printer panel to see its print mode. Please confirm that you selected tear off. If not, please change to tear off You can remove this retracting action.
4. During the process of using my printer, there is a dialog box on the computer where the printer is out of paper: Please see what the printer is lit. If it is an error light, please check if the printer's paper and ribbon are correct. If the pause light is on, just press it again to print normally.
5. My printer does not respond after printing. Please confirm whether the data cable is plugged in? If yes, please change the printer to the printer and reinstall the printer driver and printing software. Please check if it can print. If you can print, Please check if the parallel port of your previous computer is damaged. Or you can enter the following text in the Edit editing environment of Ms-Dos mode on the previous computer: .^XA.^GB600,0,100.^FO20,100^ BEN,60,Y,N^FD123456789012^FS.^XZ. If you can't print a black block, it means there is a problem with the communication.
6. My printer skips paper. I can't print normally. Please first press the FEED button a few times to see if the paper feed is normal. If it is not normal, please enter the manual calibrate in the display menu to confirm the paper. The paper type in the printer driver is set correctly. The settings in the printer are also correct. If the paper is normal, please check if the paper in the software or the driver is set correctly.
7. The barcode printed by my printer can't be scanned by the code gun. Please confirm that the relevant settings of your barcode gun are correct. The test method can be used to test the same label on other barcode machines. Sweeping out proves to be a problem with the barcode machine. If the confirmation is a problem with the barcode machine, please make a long black strip. If there is a white strip in the black strip, it indicates that the printer has a broken needle. If the broken needle is not serious You can try to get the bar code away from the broken needle. Otherwise, only replace the print head, please send it for repair.
8. After the printer is turned on, the four lights are all on. Nothing happens. There is a problem with your printer hardware, please send it for repair.
9, my printer has to break the ribbon.. Please try to reduce the printer's deep darkness, and reduce the printing pressure.
10. When my printer prints, the label is always offset to the outside. Please make sure that the label paper of your printer is installed correctly, and the back loading area has been clamped tightly. The upper limit of the paper path is correct.
11, my printer uses a serial port. But it can not print.. and ensure that the parameters in the printer are the same as in the computer host.
12, my printer has been using the same specification paper, I don't want it to be recognized every time I turn it on, waste my label paper. Please enter the panel to set, change the value of MEDIA POWER UP to FEED or NO MOTION ..
13. My barcode printer wants to print Japanese characters or other special characters. Any printer that can input any character barcode printer can print. But first you need to be able to enter this character into the barcode printing software. After that, the operation is the same as normal printing.
14, my barcode printer wants to play continuous paper.. If you are using the BARONE software, you only need to check the settings in the media label in the continuous label setting in the software.
15. My barcode printer prints lighter on one side or does not print anything on the other side. Please adjust the pressure of the print head. Please refer to the relevant contents in the manual for adjusting the pressure.
The above are the common faults and solutions for zebra printers. If you have not mentioned the problems you have encountered above, you are welcome to consult with us by phone, QQ, etc. We will try our best to answer your questions.
Shelf Bracket ,Metal Shelf Brackets,Black Shelf Brackets,Folding Shelf Bracket
Jiangmen Sunbond Houseware Manufacturing CO.,LTD , https://www.jmsunbondhw.com